SEISMIC DESIGN SPECIFICATION

1.0 SCOPE
2.0 APPLICABLE CODES, SPECIFICATIONS AND STANDARDS
3.0 SITE SEISMIC HAZARD CHARACTERISTICS
3.1 Operating Basis Earthquake Condition (OBE)
3.2 Safe Shutdown Earthquake Condition (SSE)
3.3 Seismic Zone Factor Z
3.4 Seismic Soil Factor
3.5 Seismic Near-Source Factor
3.6 Liquefaction Ppotential
3.7 Relationship between Chinese Code amax Ccoefficient and PGA
4.0 SELECTION OF SEISMIC ANALYSIS PROCEDURE
4.1 Static Lateral Force Procedure
4.2 Dynamic Analysis
5.0 STRUCTURAL SYSTEMS
5.1 General
5.2 Building Structures
5.3 Nonbuilding Structures
5.3.1 Building-Like Structures
5.3.2 Nonbuilding-Like Structures
5.4 Subsystems
6.0 SEISMIC DESIGN DATA
6.1 Occupancy Importance Ffactor I
6.2 Seismic Coefficients Ca, Cv
6.3 Determination of R and Wo
7.0 STATIC FORCE PROCEDURE
7.1 Design Base Shear
7.1.1 Buildings and Building-Like Structures
7.1.2 Nonbuilding-Like Structures
7.2 Structural Period
7.3 Vertical Distribution of Force
8.0 DYNAMIC ANALYSIS PROCEDURE
8.1 Response Spectrum Representation
8.2 Number of Mmodes
8.3 Vertical Response Spectrum
9.0 SUBSYSTEMS
10.0 ANCHOR BOLTS / CONNECTIONS
10.1 Civil / Structural
10.2 Equipment / Piping
11.0 STORAGE TANKS
12.0 VESSEL AND HEAT EXCHANGER DESIGN
13.0 PIPING DESIGN
14.0 EQUIPMENT DESIGN
15.0 LOAD, FACTORS, COMBINATIONS

ROADS, PAVING, SURFACING, SLOPE PROTECTION AND PERMANENT FENCING1. SCOPE

2. APPLICABLE CODES, SPECIFICATIONS AND STANDARDS

3. DEFINITIONS

4. ROADS AND PAVING

5. SURFACING OF UNPAVED AREAS, CONSTRUCTION ROADS AND LAYDOWN AREAS

6. SLOPE PROTECTION

7. PERMANENT FENCING

SITE PREPARATION SPECIFICATION

1. SCOPE
2. APPLICABLE CODES, SPECIFICATIONS AND STANDARDS
3. ENVIRONMENTAL CONTROL
4. EXISTING ABOVEGROUND AND UNDERGROUND SERVICES
5. TREATMENT OF UNDERGROUND CAVITIES AND FAULTS
6. TREATMENT OF SUBSOILS
7. STORM WATER AND GROUNDWATER DRAINAGE

BUILDINGS ARCHITECTURAL PERFORMANCE SPECIFICATION


1.0 Scope
2.0 References
3.0 Building Systems
4.0 Building Components and Materials
5.0 Building Design
6.0 Building Descri ption
7.0 Appendix 1 Study of Explosion Overpressures on Buildings

HVAC DESIGN SPECIFICATION

1.0 INTRODUCTION

2.0 APPLICABLE CODES, SPECIFICATIONS AND STANDARDS

3.0 EXTERNAL DESIGN CONDITIONS

4.0 INTERNAL DESIGN CONDITIONS

5.0 SYSTEM DESCRIPTIONS

6.0 NOISE AND VIBRATION

7.0 COOLING COIL CONDENSATION DRAINAGE

8.0 FIRE AND SMOKE SPREAD

9.0 AIR CONDITIONING SYSTEM REFRIGERANTS

10.0 THERMAL AND ANTI-CONDENSATION INSULATION

11.0 DUCTWORK

12.0 HVAC OVERALL SPARE COOLING CAPACITY

13.0 HVAC PLANT SPACE PROVISION

14.0 PREFERRED HVAC EQUIPMENT SUPPLIERS

15.0 MATERIALS AND WORKMANSHIP SPECIFICATION

STRUCTURAL STEEL CONSTRUCTION SPECIFICATION

1. SCOPE

2. APPLICABLE CODES, SPECIFICATIONS AND STANDARDS

3. MATERIALS

4. DETAILING OF STEEL

5. FABRICATION

6. PAINTING

7. INSPECTION

8. ERECTION

9. CLEANING

REINFORCED CONCRETE CONSTRUCTION SPECIFICATION

1.0 SCOPE 4
2.0 APPLICABLE CODES, SPECIFICATIONS AND STANDARDS 4
3.0 MATERIALS 8
3.1 GENERAL 8
3.2 CEMENT 8
3.3 AGGREGATES 9
3.4 REINFORCING MATERIAL 10
3.5 WATER 11
3.6 ADMIXTURES AND ADDITIONS 11
3.7 CHLORIDES 13
3.8 SULPHATES 13
3.9 ALKALI-AGGREGATE REACTION 13
3.10 JOINT MATERIALS 13
4.0 HANDLING AND STORAGE OF MATERIALS 13
4.1 CEMENT 13
4.2 AGGREGATES 13
4.3 REINFORCEMENT 14
4.4 OTHER MATERIALS 14
4.5 REJECTED MATERIALS 14
5.0 CONCRETE MIXES 14
5.1 CONCRETE GRADES 14
5.2 EXPOSURE CONDITIONS 15
6.0 CONCRETE WORKMANSHIP 17
6.1 PREPARATORY WORK 17
6.2 MEASUREMENT OF MATERIALS 17
6.3 CONCRETE COVER 18
6.4 WORKABILITY 19
6.5 MEASURING, MIXING, PRODUCTION AND TRANSPORTATION 20
6.6 EXTREME WEATHER PROVISIONS 21
6.7 HEAT OF HYDRATION 22
6.8 QUALITY PLAN 22
6.9 CONCRETE PLACING 24
6.10 COMPACTION AND VIBRATION 25
6.11 PROTECTION AND CURING 26
6.12 CONTROL OF COLOUR 27
6.13 CONSTRUCTION JOINTS 27
6.14 SURFACE FINISHES 28
6.15 LARGE CONCRETE POURS 28
7.0 REINFORCEMENT WORKMANSHIP 29
7.1 CUTTING, BENDING AND WELDING 29
7.2 PLACING 29
8.0 FORMWORK WORKMANSHIP 29
8.1 GENERAL 29
8.2 DESIGN 30
8.3 CONSTRUCTION OF FORMWORK 30
8.4 INTERNAL TIES 30
8.5 PREPARATION FOR CONCRETING 30
8.6 REMOVAL OF FORMWORK 31
8.7 RELEASE AGENTS 31
9.0 INSPECTION AND TESTING OF STRUCTURES AND MEMBERS 31
9.1 DIMENSIONAL DEVIATIONS 31
9.2 ADDITIONAL TESTS 31
9.3 DEFECTIVE WORK 32
10.0 ANCHOR BOLTS AND OTHER EMBEDDED ITEMS 32
11.0 GROUTING 32
11.1 TYPES OF GROUT 32
11.2 SURFACE PREPARATION 33
11.3 APPLICATION 34
12.0 PRE-CAST CONCRETE 34
APPENDIX 1 – TESTS 36

EARTHWORKS SPECIFICATION

SPECIFICATION FOR THE DESIGN, FABRICATION, INSTALLATION AND TESTING OF PRECAST CONCRETE PILES

首先还是应该感谢楼主的辛苦了！
不过，不清楚是什么东东，先下载下来再说把！